3D打印应用于髋臼骨折数字化设计的实验研究
收稿日期: 2014-03-30
网络出版日期: 2014-06-04
基金资助
国家高新科技计划863计划(2012AA02A603); 福建省莆田市科技计划项目[2010S10(3)]
The application of 3D printing technique in the research of acetabular fractures
Received date: 2014-03-30
Online published: 2014-06-04
目的 探讨髋臼骨折数字化设计及实施的可行性方案并以3D打印技术进行验证。 方法 采集52例临床髋臼骨折薄层CT扫描数据，在Mimics14.0中进行三维建模和虚拟骨折复位并在复位模型上优化预设植入钢板位置和虚拟钉道模拟、测量钉道长度，三维切割预设植入钢板部位骨块并3D打印，据此进行钢板折弯。将所有骨折块进行3D打印为实体模型结合折弯钢板进行内固定植入模拟。将钢板现实位置、螺钉方向和长度同数字化设计比较。 结果 总植入61根重建钢板，螺钉424颗，钢板植入位置和螺钉植入方向均与数字化设计高度吻合，钉道长度与数字化设计进行配对t检验，P=0.325。 结论 （1）数字化设计结合3D打印技术能在术前完成重建钢板折弯并进行手术模拟，折弯钢板模拟植入位置、螺钉植入方向、长度和虚拟设计高度一致。（2）术前折弯重建钢板对骨折复位有一定的指导价值。
吴章林 , 林海滨 , 张国栋 , 陆俭军 , 陈宣煌 , 黄华军 , 黄文华 . 3D打印应用于髋臼骨折数字化设计的实验研究[J]. 中国临床解剖学杂志, 2014 , 32(3) : 248 -251 . DOI: 10.13418/j.issn.1001-165x.201
Objective To evaluate the digital design of acetabular fractures and the feasibility of the implementation, then using the 3D printing technique to verify the results. Methods Fifty-two patients with acetabular fractures were enrolled in this study. Data of lamellar CT scanning were imported into Mimics14.0 software for 3D anatomical modeling and virtual fracture reduction. Then the default embedded steel plate location was optimized , the screw path evaluated，and the screw length measured. 3D printing technique was used to print the bone. Plates were bended based on the printing bones. Internal fixation implants were simulated based on all the printed bones and bended plates. Finally, the real operation was compared with virtual preoperative design in terms of the fixation position of plates, the direction and the length of screws. Results In the study, 61 plates and 424 screws were planted. The position of plates and the direction of screws were in high accordance with the digital design. The length of screws are compared with Paired-samples t Test and P=0.325. Conclusion Firstly, the combination of the digital design and 3D printing technique have a good application in the bending of the plates and surgery simulation before operation. The real operation is quite consistent with the simulated results. Secondly, plate bending before the real operation has a certain value in the guidance of fracture reduction.
Key words： Acetabular fractures; Digital design; 3D printing; Simulation surgery
[1] Gansslen A, Frink M, Hildebrand F, et al. Both column fractures of the acetabulum: epidemiology, operative management and long-term-results
[J]. Acta Chir Orthop Traumatol Cech, 2012, 79(2):107-113.
[2] 扈延龄，金丹，苏秀云，等. 基于三维CT数据的髋臼骨折计算机辅助虚拟手术设计
[J]. 中华创伤骨科杂志, 2008, 10(2):135-137.
[3] Rohner D, Guijarro-Martinez R, Bucher P, et al. Importance of patient-specific intraoperative guides in complex maxillofacial reconstruction
[J]. J Craniomaxillofac Surg, 2013, 41(5):382-390.
[4] Flugge TV, Nelson K, Schmelzeisen R, et al. Three-dimensional plotting and printing of an implant drilling guide: simplifying guided implant surgery
[J]. J Oral Maxillofac Surg, 2013, 71(8):1340-1346.
[5] Fu M, Lin L, Kong X, et al. Construction and accuracy assessment of patient-specific biocompatible drill template for cervical anterior transpedicular screw (ATPS) insertion: an in vitro study
[J]. PLoS One, 2013, 8(1):e53580.
[6] Karunakar MA, Goulet JA, Mueller KL, et al. Operative treatment of unstable pediatric pelvis and acetabular fractures
[J]. J Pediatr Orthop, 2005, 25(1):34-38.
[7] 张国栋，林海滨，陈宣煌，等. 基于多平面三维测量的髋臼骨折数字化内固定植入方案
[J]. 中华临床医师杂志（电子版）,2012, 6(8):2010-2015.
[8] 宋军，梅益彰，吴增城，等. 复杂髋臼骨折复位及内固定的数字技术模拟研究
[J]. 中国临床解剖学杂志, 2013, 31(4):393-396.
[9] Briffa N, Pearce R, Hill A M, et al. Outcomes of acetabular fracture fixation with ten years' follow-up
[J]. J Bone Joint Surg Br, 2011, 93(2):229-236.
[10] Gary JL, Lefaivre KA, Gerold F, et al. Survivorship of the native hip joint after percutaneous repair of acetabular fractures in the elderly
[J]. Injury, 2011, 42(10):1144-1151.
[11] 许猛，张立海，张里程，等. 复杂髋臼骨折术中应用CT扫描的意义
[J]. 中华骨科杂志, 2011, 31(11):1261-1265.
/
| 〈 |
|
〉 |
京ICP备08002354号-3
